#Fuzhou rockchip safe driver
#Fuzhou rockchip safe full
#Fuzhou rockchip safe code

#Fuzhou rockchip safe driver

Rockchip: rk3066: add clock driver for rk3066 soc

Rockchip: rk3066: add Rikomagic MK808 boardДoc: rockchip: add px30/rk3326 boards and examplesДoc: rockchip: add rk3066 Rikomagic MK808 Rockchip: tools: add rk3066 support to rkcommon.c Rockchip: rk3066-power: sync power domain dt-binding header from LinuxДЄrm: dts: rockchip: fix rk3xxx-u-boot.dtsiДЄrm: dts: rockchip: fix include rk3xxx-u-boot.dtsiДЄrm: dts: rockchip: add rk3066a-mk808.dts Sudo dd if=u-boot-dtb.img of=/dev/sda seek=16384 Program commands (SD CARD with GPT partition): Make sure boot and esp flag are set for boot partition.ДЄppend root=LABEL=linuxroot init=/sbin/init rootfstype=ext4 rootwait Partition Map for MMC device 0 - Partition Type: EFI tools/boot_merger -verbose config-flash.ini With a needle while reconnecting to the USB OTG port to a PC.Д«us 001 Device 004: ID 2207:300a Fuzhou Rockchip Electronics Company RK3066 in Mask ROM mode If bricked and no BootROM mode shows up then connect pin 8 and 9 of the NAND flash

Size of SPL and TPL must be aligned to 2kb.

#Fuzhou rockchip safe full

U-boot: read Linux kernel from SD CARD.ДЄdditionally the rk3066 requires everything the BootROM loads to beД«oot solution with full U-boot stored on SD CARD:ДЄRCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make mk808_defconfigДЄRCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make menuconfigДЄRCH=arm CROSS_COMPILE=arm-linux-gnueabihf- make all

SPL: init SDMMC and read U-boot from SD CARD. With CONFIG_TPL_ROCKCHIP_EARLYRETURN_TO_BROM=y this first stage is combined withДЇor rk3066 with NAND flash and U-boot this gives the following stages: It always enters at offset 0x804 after a 4 ASCII character 'RK30' header. Then the remainder to offset 0xc00 in the SRAM. Image in two steps: first 1KB to offset 0x800 in the SRAM and Similar to the already supported rk3188, the BootROM will attempt to load up the first stage Of that 64k size only 32kb sram - 2kb bootrom is available for the first stage. The size of a full U-boot binary is too large for the internal SDRAM memory. Unlike later SoC models the rk3066 BootROM doesn't have SDMMC support. If all boot options fail then enter into BootROM mode on the USB OTG port. Supported system boot from the following devices:

#Fuzhou rockchip safe code

It also includes on-board NANDД«oot procedure flow for a Rockchip rk3066 SoC:ДЎ.Read 2K SDRAM initialization image code to internal SRAMДў.Run image code to do SDRAM initialization MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port, To: kever.yang +Cc: sjg, philipp.tomsich, lukma, seanga2, u-boot ` (15 more replies) 0 siblings, 16 replies 22+ messages in thread 1:29 ` rockchip: rk3066-power: sync power domain dt-binding header from Linux Johan Jonker SPDX-License-Identifier: GPL-2.0-only /* * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd * Author:Mark Yao */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #ifdef CONFIG_DRM_ANALOGIX_DP #include #endif #include ' rockchip_drm_drv.h' #include ' rockchip_drm_gem.h' #include ' rockchip_drm_fb.h' #include ' rockchip_drm_vop.h' #include ' rockchip_rgb.Add Rikomagic MK808 board All of help / color / mirror / Atom feed * Add Rikomagic MK808 board 1:29 Johan Jonker